8-Year Result of a Lateral Window Opening using an LS-reamer with a Small Vertical Incision

허영구 원장님 Dr. Heo

Author
Dr. Young-Ku Heo, DDS, MDS, PhD

Director of Global Academy of Osseointegration
Seoul, Korea



슬라이드4
A 56-year-old male
His medical condition was normal and non-smoker.
Panoramic view. The residual bone is about 4mm at #15 and 16 area. 6mm at #27.
슬라이드3
Maxillary right second premolar and the first and second molars were missing. The alveolar ridge had enough bone and sufficient attached gingiva. The first premolar needed RCT and crown.

슬라이드4
Panoramic view. The residual bone is about 4mm at #15 and 16 area. 6mm at #27.
Flapless implant placement surgery with SLA technique using LS- reamer through a small vertical incision was planned.


슬라이드7
A lateral hole was made by Ф7.5mm LS-reamer using 2000 rpm with copious saline irrigation. A large lateral hole can allow easy elevation of the membrane from the anterior to the posterior.

슬라이드8
A lateral hole was formed and the sinus mucosal membrane was elevated with the microelevators in the SLA kit. The residual bone height of #17 area was about 9mm. This did not need a bone graft, just membrane detachment to make a Class II CMI fixation.

슬라이드5
10mm vertical incision was done above the second premolar. The second premolar area was chosen for the best location of a lateral hole, which should be at the most anterior and most inferior area from the most anterior implant.

슬라이드6
The flap was retracted for inserting the LS-reamer. Lateral wall of the maxillary sinus was seen from the small opening. To elevate the membrane for 3 implants, the reamer should be the largest one (Ф7.5mm).

슬라이드9
A lateral hole was made by Ф7.5mm LS-reamer using 2000 rpm with copious saline irrigation. A large lateral hole can allow easy elevation of the membrane from the anterior to the posterior.

슬라이드10
Simple interrupted sutures were made. Simultaneous implant placement was planned with a punching technique because there was sufficient attached gingiva and a wide ridge.

슬라이드11
Punching the midcrestal attached gingiva with Ф5mm tissue punch. At least 2mm attached gingiva around the implant should exist for tissue punching technique.

슬라이드12
3 positions were prepared for punching and the round tissue was detached for simultaneous implant placement.

슬라이드13
Three CMI EB (Neobiotech, Seoul Korea) fixtures were placed: #15: EB4511, #16: EB510, #17:EB5010.
The bone densities and ITV (insertion torque value) were D320 with 35 Ncm, D320 with 40 Ncm, and D342 with 35 Ncm for #15, 16, and 17 respectively.


슬라이드14
Healing abutments were connected. There were more than 2mm of attachment gingiva around the healing abutments.

슬라이드15
Lateral opening with a LS-reamer and implant placement simultaneously.
http://gg.gg/mov7-2


슬라이드16
Panoramic view after the sinus graft and implant placement in the right side. Sufficient bone grafting was done at #15, and 16 area. At #17, only membrane was elevated and the implant was placed without bone grafting.

슬라이드17
After 10 days, the incision area was completely healed.
The patient felt almost no pain or swelling. That is the big advantage of the SLA technique with minimal vertical incision.


슬라이드18
A periapical radiograph after 3 months healing. ISQ values were 75-80. Final impression was made at the visit.

슬라이드19
A definitive 3-unit PFM FPD (SCRP) was fabricated.

슬라이드20
Occlusal surface of the SCRP. Its design had screw holes but metal chimneys were not formed in order to enhance the esthetic aspect.

슬라이드21
Finally, the SCRP superstructure was cemented with a permanent resin cement in the mouth.

슬라이드22
The whole unit SCRP was removed from the fixtures by unscrewing. Access cement was removed and crown margins were polished at the outside of the mouth. The SCRP has many advantages: crown margin can be positioned at the sub-gingival area and emergence profile can be reproduced by crown contour.

슬라이드23
The occlusal screw holes were filled with a permanent composite resin. It is a retrievable prosthesis like a screw retained one.

슬라이드24
Buccal view after delivery of the prosthesis.

슬라이드25
Periapical radiograph after delivery of the final prosthesis.

슬라이드26
Panoramic view after delivery of the prosthesis.

슬라이드27
8 years of follow-up panoramic view. All implants were well maintained without any noticeable bone loss.

슬라이드28
8 years of follow-up periapical view. Bone levels were well maintained at the bioseal level.

Flapless implant placement surgery with SLA technique using LS- reamer through a small vertical incision was planned.

975 Total Views 5 Views Today
0 Comments

Leave a reply

CONTACT US

We're not around right now. But you can send us an email and we'll get back to you, asap.

Sending

Copyright (c) GAO Forum. All Rights Reserved.

 

Forgot your details?