Maxillary Posterior Multiple Teeth Replacement with Class I, II, and III CMI Fixations

허영구 원장님 Dr. Heo

Author
Dr. Young-Ku Heo, DDS, MDS, PhD

Director of Global Academy of Osseointegration
Seoul, Korea



슬라이드4
Pre-operative panoramic radiograph. The heights of residual alveolar bone in the areas of #16 & #27 were measured as 7-8mm.
슬라이드3
Pre-operative intra-oral photograph.
Bridge of four anterior teeth was removed. #16, #15, #12, #24, #25 & #27 were missing.


슬라이드4
Pre-operative panoramic radiograph.
The heights of residual alveolar bone in the areas of #16 & #27 were measured as 7-8mm.
Class III sinus bone graft using the SCA kit with simultaneous implant installation was planned.


슬라이드5
Occlusal view of right side pre-operative intra-oral photograph.
Abundant keratinized gingiva was seen. Bony torus of buccal side could be seen.


슬라이드6
Occlusal view of left side pre-operative intra-oral photograph.
Abundant keratinized gingiva was seen.


슬라이드7
Removed incised keratinized gingiva.

슬라이드8
After serial drilling, 2.4mm diameter S-reamer of the SCA kit with 8mm stopper was used at the area of #16 due to 8mm residual alveolar bone height as measured with panoramic radiograph.
After the 2.4 diameter S-reamer, the 2.8 diameter S-reamer was applied with caution to enlarge the hole of cortical bone at the maxillary sinus floor.


슬라이드9
Allograft (RegenOss™) was inserted into the space of the elevated sinus membrane. Bone graft material was applied with the bone carrier of the SCA kit. The bone carrier was designed to hold 0.05cc at one time. A total of 0.3cc was placed.

슬라이드10
Bone graft material of the apical side was dispersed with the bone spreader from the SCA kit using a handpiece with a speed of 50-80 rpm.

슬라이드11
After bone graft, trans-mucosal IT type CMI implant (5.0X10.0) was ready for #16 area.

슬라이드12
Fixture at #16 area was placed for optimal depth.

슬라이드13
Another trans-mucosal IT type CMI implant (4.0X10.0) was planned for the area of #15.

슬라이드14
Fixture was placed at the area of #15.

슬라이드15
The initial torque of the #15 fixture was about 35 Ncm.

슬라이드16
Two trans-mucosal (non-submerged) type implants were positioned at the place of #16 & #15 without an elevating flap.

슬라이드17
Healing abutments were connected due to sufficient insertion torque.

슬라이드18
Incised keratinized gingiva was removed with surgical curette. The site of #27 was prepared for the same way.

슬라이드19
The site of #27 was prepared with the S-reamer from the SCA kit to perform a crestal sinus approach along 7-8mm residual alveolar bone height. After opening of cortical bone at the sinus floor area, Aqua tap of the Sinus All kit was connected to the drilling site for elevating the Schneiderian membrane with hydraulic pressure.

슬라이드20
Aqua valve with saline syringe was linked to the access hole of the firmly fixed Aqua Tap.

슬라이드21
The same amount of saline as planned for sinus membrane elevation was prepared in the syringe. The plunger of the syringe was moved forward and backward with attention not to cause the sinus membrane to tear. After elevation, bone graft material was inserted in the usual manner.

슬라이드22
IT type wide neck CMI implant (5.0X10.0) was placed at the site of #27 with enough insertion torque.

슬라이드23
Healing abutments were coupled with fixtures.

슬라이드24
Post-operative panoramic radiograph after both side maxillary sinus bone graft and implants placement. Dome shaped bone graft material at the apex of #16 & #27 was observed.

슬라이드25
Intra-oral photograph 3 weeks after surgery. Impression of #16, #15, #24 & #25 was taken. After controlling height of ready-made abutments, they were connected to the fixtures. Bite registration was made with silicone rubber material.

슬라이드26
Periapical radiograph three weeks after operation.
Abutments were placed in position, and alveolar bone around fixtures were well maintained


슬라이드28
Final prostheses of right maxilla were delivered one and a half months later after surgery.

슬라이드29
Lateral view of right maxilla after delivery of restorations.

슬라이드27
Periapical radiograph of posterior maxilla five months after surgery. The alveolar bone around fixtures appeared firm and stable.

슬라이드30
Panoramic radiograph after delivery of prostheses at both sides of the posterior maxilla.

슬라이드31
Lateral view of left maxilla after treatment.

슬라이드32
Panoramic radiograph five months after operation.
All prostheses of implants were delivered.
The bone graft material inserted with the SCA kit at the apical site of #16 & #27 was stable.


Class III sinus bone graft using the SCA kit with simultaneous implant installation was planned.

1626 Total Views 1 Views Today
0 Comments

Leave a reply

CONTACT US

We're not around right now. But you can send us an email and we'll get back to you, asap.

Sending

Copyright (c) GAO Forum. All Rights Reserved.

 

Forgot your details?